Industrial Integrator

Product Details
Customization: Available
Transport Package: Carton
Specification: 90*61*18mm
Manufacturer/Factory & Trading Company
Gold Member Since 2021

Suppliers with verified business licenses

Audited Supplier

Audited by an independent third-party inspection agency

Plant Area
897 square meters
Management System Certification
ISO9001:2015
  • Industrial Integrator
  • Industrial Integrator
  • Industrial Integrator
  • Industrial Integrator
  • Industrial Integrator
Find Similar Products

Basic Info.

Model NO.
D1.1, 1.2, 1.3
Trademark
MEATROL
Origin
Shanghai, China
HS Code
8504109000
Production Capacity
1000

Product Description

D1 Industrial integrator
D1 is a Industrial Rogowski coil integrator installation in distribution box,in a plastic 1 module DIN-RAIL enclosure, powered directly from the mains.
What does Integrator do?
Rogowski coil output is weak voltage mV signal,D1 has ability to amplify and convert it to standard signal which could be catched by multimeter and scope.
Rogowski coil output is proportional to the frequency of the measured current, the signal equalization ensure a linear response on a wide frequency range. D1 allows to use coils on different electrical network frequencies, keeping the same output level over the frequencies.
 An integrator is essential to equalize and shift by 90° the output signal from the Rogowski coils. It consists of an active electronic circuit with negligible offset and a good linearity.
Feature
D1 can be combined with any model and size of Y-FCT or FCT Rogowski coils.
The available values are: 0-5VDC,0-5VAC,4-20mAC.
On request the input value can be customized according to the application.
D1 and Rogowski coil is a very flexible system, suitable for high power load analysis, impulsive current monitoring, DC ripple measurement, etc.
Due to its specific features, flexible Rogowski coil is an extremely comfortable solution for current measurement and can be used in a number of cases where traditional current transducer is not the adequate solution.
What is a Rogowski coil?
Rogowski coils have been used for the detection and measurement of electric currents for decades. They are based on a simple principle: an "air-cored" coil is placed around the conductor in a toroidal fashion and the magnetic field produced by the current induces a voltage in the coil. The voltage output is proportional to the rate of change of current. This voltage is integrated, thus producing an output proportional to the current.
By using precision winding techniques, especially developed for the purpose, the coils are manufactured so that their output is not influenced by the position of the conductor within the toroid, and to reject interference from external magnetic fields caused, for example, from nearby conductors.
Basically, a Rogowski coil current measuring system consists of a combination of a coil and conditioning electronics.Rogowski coil current transducers are used for the AC measurement.
They can be used in similar circumstances to current transformers but for many applications they have considerable advantages:
Wide dynamic range.
High linearity.
Very useful with large size or awkward shaped conductors or in places with limited access. Thanks to the structure without hard core, the coil can be easily manufactured according to the application or to the available space.
Unlike traditional current transducers, there is no danger from open-circuited secondaries.
They cannot be damaged by large overloads.
They are non-intrusive. They draw no power from the main circuit carrying the current to be measured.
They are also light weighted and in some applications are light enough to be suspended on the conductor being measured.
The transducer does not measure direct currents but, unlike a current transformer, it can carry out accurate measurements of AC component even if there is a large superimposed DC component, since there is no iron core causing saturation. This feature is particularly useful for measuring ripple currents for example in battery charging systems.
Model D1.1 D1.2 D1.3
Rated output 5V AC rms 4V DC(true-rms) 4-20mA
Maximum Output(overload) 10V AC rms 4.8V DC 25mA
Output Ripple factor 0.5% Default 5% (relay to Response time)
Response time ≤1us Default 100ms(adjustable)
Power consumption 150mW 200mW
Bandwidth 10Hz to 20kHz 20-2kHz
Rated Input 100A
600A
1000A
3000A
6000A
Read Accuracy 0.5% typical at 1%(≥10A) to 200% of rated Current @25ºC
Phase error ≤0.5°
Linearity ±0.2% of reading(1% to 200% of range)
Minimum Current measurement 1A (Ripple 100mA)
Output on 0A                                                                                                                                           (zero drift) 2mV
Temperature drift 200ppm/ºC
Weight 60g
Dimension 90*61*18mm
Power supply  12V or 24V(best performance on 24V default)
Operating temperature -20ºC to 70ºC
Storage temperature -30ºC to 90ºC
Relative humidity: 80% max.without condensation
Protection degree: IP20
Other requirements,please contact us to OEM.
Safety and warning notes
In order to guarantee safe operation of the transducer and to be able to make proper use of all features and functions,please read these instructions thoroughly!Safe operation can only be guaranteed if the transducer is used for the purpose it has been designed for and within the limits of the technical specifications
Caution!Risk of danger
Ignoring the warnings can lead to serious injury and/or cause damage!
The electric measuring transducer may only be installed and put into operation by qualified personnel that have received an appropriate training,The corresponding national regulations shall be observed during installation and operation of the transducer and any electrical conductor.The transducer shall be used in electric/electronic equipment the respect to applicable standards and safety requirements and in accordance with all the related systems and components manufacturers' operating instructions.
Caution!Risk of electrical shock
When operating the transducer,certain parts of the module may carry hazardous live voltage(e.g.primary conductor).The user shall ensure to take all measures necessary to protect against electrical shock.The transducer is a build-in device containing conducting parts that shall not be accessible after installation.A protective enclosure or additional insulation barrier may be necessary.Installation and maintenance shall be done with the main power supply disconnected except if there are no hazardous live parts in or in close proximity to the system and if the applicable national regulations are fully observed.
Safe and trouble-free operation of this transducer can only be guaranteed if transport,storage and installation are carried out correctly and operation and maintenance are carried out with care.
WARING!
Do not stress the coil by applying any kind of mechanical force(ie.twisting,puncturing,excessive pressure,tight bending,etc.) which will dramatically degrade the device's accuracy.Industrial IntegratorIndustrial Integrator
 

Send your message to this supplier

*From:
*To:
*Message:

Enter between 20 to 4,000 characters.

This is not what you are looking for? Post a Sourcing Request Now
Contact Supplier