High Frequency Integrator

• Customization: Available
• Transport Package: Carton
• Specification: 86*90*29mm
• Model NO.: HF
• Trademark: MEATROL
• Origin: Shanghai, China
• HS Code: 8504109000
• Production Capacity: 1000

Product Description

HF High Frequency integrator
   HF is a High Frequency Rogowski coil integrator, in a compact shield aluminium alloy enclosure, powered directly from the mains.It is providing the measurement of all kinds of waveforms like 3/5μs, 8/20μs,10/350μs,frequency
from 100kHz to 1MHz, it also features in direct connection to oscilloscope
What does Integrator do?
• Rogowski coil output is weak voltage mV signal,HF has ability to amplify and convert it to standard signal which could be catched by multimeter and scope.
• Rogowski coil output is proportional to the frequency of the measured current, the signal equalization ensure a linear response on a wide frequency range. TP allows to use coils on different electrical network frequencies, keeping the same output level over the frequencies.
• An integrator is essential to equalize and shift by 90° the output signal from the Rogowski coils. It consists of an active electronic circuit with negligible offset and a good linearity.
Feature
   TP can be combined with any model and size of Y-FCT or FCT Rogowski coils.
   The available values are: 0-12V peak
   On request the input value can be customized according to the application.
   TP and Rogowski coil is a very flexible system, suitable for high power load analysis, impulsive current monitoring, DC ripple measurement, etc.
   Due to its specific features, flexible Rogowski coil is an extremely comfortable solution for current measurement and can be used in a number of cases where traditional current transducer is not the adequate solution.
What is a Rogowski coil?
    Rogowski coils have been used for the detection and measurement of electric currents for decades. They are based on a simple principle: an "air-cored" coil is placed around the conductor in a toroidal fashion and the magnetic field produced by the current induces a voltage in the coil. The voltage output is proportional to the rate of change of current. This voltage is integrated, thus producing an output proportional to the current.
    By using precision winding techniques, especially developed for the purpose, the coils are manufactured so that their output is not influenced by the position of the conductor within the toroid, and to reject interference from external magnetic fields caused, for example, from nearby conductors.
    Basically, a Rogowski coil current measuring system consists of a combination of a coil and conditioning electronics.Rogowski coil current transducers are used for the AC measurement.
    They can be used in similar circumstances to current transformers but for many applications they have considerable advantages:
• Wide dynamic range.
• High linearity.
• Very useful with large size or awkward shaped conductors or in places with limited access. Thanks to the structure without hard core, the coil can be easily manufactured according to the application or to the available space.
• Unlike traditional current transducers, there is no danger from open-circuited secondaries.
• They cannot be damaged by large overloads.
• They are non-intrusive. They draw no power from the main circuit carrying the current to be measured.
• They are also light weighted and in some applications are light enough to be suspended on the conductor being measured.
    The transducer does not measure direct currents but, unlike a current transformer, it can carry out accurate measurements of AC component even if there is a large superimposed DC component, since there is no iron core causing saturation. This feature is particularly useful for measuring ripple currents for example in battery charging systems.

Model	HF
Rated output	1V AC peak
Maximum Output(overload)	12V AC peak
Rated ratio	1kA/1V 10kA/1V 50kA/1V Minimum ratio:1000A/1V
Read Accuracy	2% typical at 10% to 1000% of rated Current @25ºC
Phase error	≤0.5°
Linearity	±0.5% of reading(10% to 1000% of range)
Minimum Current measurement	10% of rated ratio
Typical waveform	1/5μs,8/20μs,10/350μs
Response time	≤1us
Power consumption	300mW
Output on 0A                                                                                                                                         (zero drift)	≤10mV
Temperature drift	200ppm/ºC
Weight	160g
Dimension	86*90*29mm
Power supply	4-12V DC (included 85-265AC to 12V DC adaptor)
Operating temperature	-20ºC to 70ºC
Storage temperature	-30ºC to 90ºC
Relative humidity	80% max.without condensation
Protection degree	IP20
Terminal(Locks type)	Input:locked with H-FCT signal cable Output:BNC female terminal with 2m BNC male terminal cable     Power:DC-DC terminal 5.5*2.0mm² with 85-265VAC adaptor
Other requirements,please contact us to OEM.

Safety and warning notes
   In order to guarantee safe operation of the transducer and to be able to make proper use of all features and functions,please read these instructions thoroughly!Safe operation can only be guaranteed if the transducer is used for the purpose it has been designed for and within the limits of the technical specifications.
Caution!Risk of danger
  Ignoring the warnings can lead to serious injury and/or cause damage!
  The electric measuring transducer may only be installed and put into operation by qualified personnel that have received an appropriate training,The corresponding national  regulations shall be observed during installation and operation of the transducer and any electrical conductor.The transducer shall be used in electric/electronic equipment the respect to applicable standards and safety requirements and in accordance with all the related systems and components manufacturers' operating instructions.
Caution!Risk of electrical shock
   When operating the transducer,certain parts of the module may carry hazardous live voltage(e.g.primary conductor).The user shall ensure to take all measures necessary to protect against electrical shock.The transducer is a build-in device containing conducting parts that shall not be accessible after installation.A protective enclosure or additional insulation barrier may be necessary.Installation and maintenance shall be done with the main power supply disconnected except if there are no hazardous live parts in or in close proximity to the system and if the applicable national regulations are fully observed.
   Safe and trouble-free operation of this transducer can only be guaranteed if transport,storage and installation are carried out correctly and operation and maintenance are carried out with care.
WARING!
Do not stress the coil by applying any kind of mechanical force(ie.twisting,puncturing,excessive pressure,tight bending,etc.) which will dramatically degrade the device's accuracy.
For order codes, you can check the product specification